Altana Haze-Gloss Manual Manual de usuario Pagina 26
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
10. Interface Description
10. Interface Description
The haze-gloss is equipped with a
serial interface (RS 232 C), which
allows for data handling and control of
the unit with a PC.
A 9-pin SUB-D connector is mounted
on the measuring unit for transfer
purposes.
haze-gloss PC
3 TxD -------- RxD 3
2 RxD -------- TxD 2
7 RTS -------- CTS 5
8 CTS -------- RTS 4
5 ------ GND ------ 7
Transfer Rate and Format
The serial asynchronous transfer of
data is specified in the measuring unit
and is performed according to the
following format:
2400 baud, 8 data bits, no parity,
1 stop bit
Control Commands
'O' (ASCII) starts the on-line operation
(ONLINE appears on the display)
- the haze-gloss keyboard is blocked
- automatic measurement is started
using the operating switch
SET UP Status of haze-gloss is
transferred to the computer:
(1 byte each INTEGER)
- Current Mode:
0 = sample mode
1 = statistic mode
- Selected Geometry:
0 = haze
1 = 20°
2 = 60°
3 = 85°
5 = 20° & 60°
6 = auto-range
7 = 60° & 85°
- Current Downward Movement:
0 = lower 4 cm
1 = lower 7 cm
- Target Illumination:
0 = off
1 = on
- Decimal Point:
0 = display without decimal point
1 = display with decimal point
1
6
5
9
The haze-gloss is equipped with a
serial interface (RS 232 C), which
allows for data handling and control of
the unit with a PC.
A 9-pin SUB-D connector is mounted
on the measuring unit for transfer
purposes.
haze-gloss PC
3 TxD -------- RxD 3
2 RxD -------- TxD 2
7 RTS -------- CTS 5
8 CTS -------- RTS 4
5 ------ GND ------ 7
Transfer Rate and Format
The serial asynchronous transfer of
data is specified in the measuring unit
and is performed according to the
following format:
2400 baud, 8 data bits, no parity,
1 stop bit
Control Commands
'O' (ASCII) starts the on-line operation
(ONLINE appears on the display)
- the haze-gloss keyboard is blocked
- automatic measurement is started
using the operating switch
SET UP Status of haze-gloss is
transferred to the computer:
(1 byte each INTEGER)
- Current Mode:
0 = sample mode
1 = statistic mode
- Selected Geometry:
0 = haze
1 = 20°
2 = 60°
3 = 85°
5 = 20° & 60°
6 = auto-range
7 = 60° & 85°
- Current Downward Movement:
0 = lower 4 cm
1 = lower 7 cm
- Target Illumination:
0 = off
1 = on
- Decimal Point:
0 = display without decimal point
1 = display with decimal point
1
6
5
9
- Reectometer 4
- Cat.No. AG-4601 4
- Version: 2.6 5
- Copyright 1990 5
- 1. Safety Information 6
- 2. System Description 7
- 3. Start-Up 8
- 220-240 V 9
- Version: 2 10
- Copyright 1990 10
- 4. Operation 12
- 5. Calibration 13
- 7. Practical Measuring 19
- Hints 19
- 8. Measurement Series 23
- and Statistic 23
- 9. International 25
- Specifications 25
- 10. Interface Description 26
- 11. Technical Data 28
- 12. Sources of Errors 29
- 20° Lamp defect ! 30
- Continue: 30
- 13. Ordering Guide 31
- Reektometer 34
- Best.-Nr. AG-4601 34
- Gesamtansicht 37
- 1. Sicherheitshinweise 38
- 3. Inbetriebnahme 40
- 4. Handhabung 44
- HAZEKALIBRATION 47
- Hazekalibration ok 47
- 6. Einstellen der 49
- Geräteparameter 49
- SET-UP Menü 49
- 7. Meßpraxis 51
- 9. Normen 57
- 10. Schnittstellen 58
- beschreibung 58
- 11 . Technische Daten 60
- 12. Fehlerquellen 61
- 20° Lampe defekt ! 62
- 13. Lieferhinweise 63
- Brillancemètre 66
- N° Ref. AG-4601 66
- 1. Description du 70
- système 70
- 2. Démarrage 71
- Installation 72
- Version: 2.95 73
- Copyright 1991 73
- 3. Fonctionnement 75
- ETALONNAGE HAZE 78
- Etal. Haze ok 78
- 5. Sélection des 80
- paramètres 80
- de l’instrument 80
- Menu SET UP 80
- 6. Indications pratiques 82
- concernant les 82
- mesures 82
- 8. Spécifications 87
- internationales 87
- 9. Description de 88
- l’interface 88
- 10. Données techniques 90
- 11. Sources d’erreur 92
- 12. Liste des 94
- composants et 94
- accessoires 94
- Riettometro 96
- No di cat. AG-4601 96
- 1. Descrizione Impianto 100
- 2. Avvio 101
- Verpackung mit Person 102
- Versione: 2.8 103
- 3. Funzionamento 105
- CALIBRAZIONE HAZE 108
- Calibrazione Haze ok 108
- 5. Selezionare i 110
- parametri dello 110
- strumento 110
- Menù SET UP 110
- Ausschnitt Sensor 111
- 6. Consigli pratici di 112
- misurazione 112
- AUTO-RANGE 113
- 8. Specicazioni 117
- Internazionali 117
- 9. Descrizione 118
- Interfaccia 118
- 10. Dati tecnici 120
- 11. Fonti di errore 122
- 12. Indice 124
- EG - Konformitätserklärung 125
- 228 012 718 EDFI 0811 128
Relacionado con productos y manuales para Instrumentos de medición Altana Haze-Gloss Manual
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales