Altana Haze-Gard Plus Operating Instructions Manual de usuario Pagina 37
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
s Selected language (byte 1)
00h = German
01h = English
02h = French
03h = Italian
04h = Spanish
s Current mode (byte 2)
00h = T
01h = H
02h = C
03h = T&H
04h = T&C
05h = H&C
06h = T&H&C
s Number of valid individual
readings (byte 3)
00h = Only first reading is valid
01h = First and second readings
are valid
02h = All three readings are valid
s Sample, Statistics or Results
(byte 4)
00h = Sample
01h = Statistics
02h = Results
s Continuous Mode (byte 5)
00h = No
01h = Yes
s Calibration valid (byte 6)
00h = No
01h = Yes
s Beep (byte 7)
00h = Off
01h = On
s Display contrast
s Versionnumber LSB
s Versionnumber MSB
The following conventions apply for
operating the instrument controls
from the PC:
00h = Statistics
01h = Delete last
02h = Results
03h = Delete all
04h = Operate
05h = Setup
06h = Reference
08h = Transmittance
09h = Haze
0Ah = Clarity
The instrument acknowledges each
control command with 2 characters
(bytes).
First byte: control command (echo)
Second byte: "!" (21h)
If the PC sends the instrument a 4
(= operate) while the instrument is
in any measuring mode, a meas-
urement will be started. When the
first measurement reading is
available, the instrument sends a
66h (ASCII code for lower-case ‘f’)
to the PC (readout). Then the
measured values are transmitted.
Data is always transmitted for all
three parameters. The status string
contains the information about the
validity and sequence of readings
(bytes 2 and 3).
For the measured value, four ASCII
characters followed by a 0 byte are
transmitted.
Example: 39h+35h+2Ch+34h+00h
is equivalent to a measured value of
95.4.
- Cat.No. AT-4725 and AT-4726 4
- Table of Contents 4
- 1. Safety Information 6
- 2. System Description 8
- 3. Startup 9
- Setting Up 10
- Power-Up 11
- 4. Operation 14
- 5. Calibration 17
- Monitoring Test Equipment 20
- 5.2 Cleaning the Standards 20
- 5.4 Calibration with Taber 21
- Abrasion Holder 21
- Change Cal Value 22
- Input Trans Std 22
- Input Clarity Std 22
- Save Std Values 22
- 6. SET-UP Menu: Setting 23
- Instrument Parameters 23
- deleted 27
- 9. Parameters 30
- 10. Changing Lamps and 34
- 11. Interface Description 36
- 12. Technical Specifications 39
- 13. Ordering Guide 41
- Printer 42
- not ready 42
- Invalid date 43
- Memory 43
- full 43
- Cal values are 44
- set to default 44
- Online Mode 44
- Keyboard inactive 44
- Best.-Nr. AT-4725 46
- Best.-Nr. AT-4726 46
- Best.Nr. AT-4725 und AT-4726 48
- Inhaltsverzeichnis 48
- 1. Sicherheitshinweise 50
- 2. Systembeschreibung 52
- 3. Inbetriebnahme 53
- Aufstellung 54
- Version: 1.0 55
- Copyright 1994 55
- 4. Handhabung 58
- 5. Kalibration 61
- 5.1 Zusatzstandards zur 64
- Prüfmittelüberwachung 64
- 5.2 Reinigung der Standards 64
- 5.3 Kalibrierwerte ändern 65
- Kalibrierstd. ändern 66
- Transmission Std 66
- Clarity Standard 66
- Werte sichern 66
- Abbruch: SET UP 66
- STATISTIK n= 5 69
- 9. Die Meßgrößen 74
- 10. Lampen- und 78
- Sicherungswechsel 78
- 12. Technische Daten 83
- 13. Lieferhinweise 85
- Drucker 86
- nicht bereit 86
- Ungültige 87
- Datumseingabe 87
- Statistikspeicher 87
- ist voll 87
- Kalibrierdaten 88
- werden berichtigt 88
- Online Modus 88
- Tastatur gesperrt 88
- N° Réf. AT-4725 90
- N° Réf. AT-4726 90
- N°Réf. AT-4725 et AT-4726 92
- Table des matières 92
- 1. Consignes de sécurité 94
- 2. Description du système 96
- 3. Démarrage 97
- Installation 98
- Mise sous tension 99
- Std.transmission 100
- Standard clarity 100
- PRECHAUFFAGE 101
- 4. Fonctionnement 102
- 5. Etalonnage 105
- porte de haze 106
- Pret: OPERATE 106
- ETALONNAGE 106
- Mesure du 100% 106
- svp decouvrir la 106
- 5.1 Etalons supplémentaires 108
- 5.2 Nettoyage des étalons 108
- 5.3 Modification des valeurs 109
- Changer Etalonnage 110
- Du transm.std 110
- Du clarity std 110
- Enregistre Valeur 110
- Quitter: SET UP 110
- 6. Menu "SET-UP“: 111
- Sélection des 111
- paramètres de 111
- l’instrument 111
- 7. Mesures en série et 113
- statistiques 113
- 8. Mode continu 116
- 9. Les grandeurs de 118
- mesure 118
- 10. Changement des 122
- lampes et des fusibles 122
- 12. Données techniques 127
- 13. Liste des 129
- composants 129
- et accessoires 129
- 14. Messages d’erreur 130
- Memoire statistique 131
- pleine 131
- Valeurs de lʻetalon 132
- Mode Online 132
- clavier bloque 132
- No di cat. AT-4725 134
- No di cat. AT-4726 134
- No. di cat. AT-4725 e AT-4726 136
- 1. Informazioni sulla 138
- sicurezza 138
- 2. Descrizione del 140
- sistema 140
- 3. Inizializzazione 141
- Impostazioni 142
- Accensione 143
- Standard di trasmittanza 144
- Standard di clarity 144
- MEMORIA STATISTICA 144
- RISCALDAMENTO 145
- 4. Funzionamento 146
- 5. Taratura 149
- 5.1 Standard supplementari 152
- 5.2 Pulizia degli standard 152
- 5.3 Modifica dei valori 153
- Standard di 154
- Confermare: OPERATE 154
- Escape: SET UP 154
- 6. Menu SET-UP: 155
- Impostazione dei 155
- parametri dello 155
- strumento 155
- STATISTIC n= 5 157
- H 30.6 m= 30.1 157
- s= 0.5 157
- C 20.8 m= 20.3 157
- s= 0.4 157
- Eseguire la 161
- 9. Parametri 162
- 10. Sostituzione di 166
- lampade e fusibili 166
- 12. Dati tecnici 171
- 13. Guida agli Ordini 173
- Data non valida 175
- Misurazione di 175
- Memoria piena 175
- Valori di taratura 176
- Modalità in Linea 176
- Tastiera inattiva 176
- EG - Konformitätserklärung 177
- 238 013 796 EDFI 0805 180
Relacionado con productos y manuales para Instrumentos de medición Altana Haze-Gard Plus Operating Instructions
Instrumentos de medición Altana Haze-Gard Plus Storing and Handling of the Standar Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Altana Byko-Spectra Effect Short Instructions Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Altana Byko-Spectra Effect Short Instructions Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Altana Byko-Spectra Effect Short Instructions Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Altana Byko-Spectra Effect Short Instructions Manual de usuario
(2 paginas)
(2 paginas)
Instrumentos de medición Altana Byko-Spectra Effect Short Instructions Manual de usuario
(2 paginas)
(2 paginas)
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales